CB series gear pumps are commonly used in agricultural machinery hydraulic system. After a period of gear pump performance, its performance will decline, the survey shows that the main form of gear pump damage is uniform sleeve and gear wear and scratches, the average wear is generally between 0.02-0.50mm, The depth of the mark is usually between 0.05-0.50mm. Due to agricultural time constraints, the urgent need to repair in a short time after damage, but also must take into account the service life of the gear pump after the second life and maintenance costs and maintenance work site operability. This article describes techniques for arc spraying and sticking in quick fixes. Arc spraying repair technology of gear pump 1, the principle and characteristics of arc spraying Arc coating technology in the past 20 years in materials, equipment and applications developed rapidly, its working principle is to be two sprayed wire as a melting electrode, driven by the motor variable speed, the intersection of the muzzle to produce a short circuit arc and lead to melting, with the aid of Compressed air is atomized into particles and sprayed at high velocity onto the pre-treated work surface to form a coating. It is a spray high efficiency, high bonding strength, good coating quality spraying method, with high energy efficiency, equipment investment and low cost, simple equipment, convenient and flexible operation, easy site construction and safety advantages. 2, gear pump arc spraying repair process Bushing bore, sleeve outer circumference, gear shaft and pump casing uniform wear and scratches in the 0.02-0.20mm, should adopt high hardness, strong combination with the body parts, good wear resistance arc spray repair Process. Arc spraying process: the working surface pretreatment → preheat → spray bonding the bottom → spraying the working layer → cooling → coating processing. Spraying process, the requirements of the workpiece without oil, no rust, surface roughness, preheating temperature is appropriate, the bottom combined with a solid, smooth working layer, the material particles melt-bonded reliable, good wear resistance and corrosion resistance. Spray coating quality and workpieces surface treatment and spraying process has a great relationship, therefore, choose the appropriate surface treatment and spraying process is very important. In addition, in the spraying and spraying process with a thin metal or copper skin will be painted surface adjacent to the non-sprayed portion of the bundle ⑴ workpiece surface pretreatment The basic bonding strength of the coating is related to the substrate cleanliness and roughness. Before spraying, the basic surface cleaning, degreasing and surface roughening and other pretreatment is an important process spraying process. The first part of the spray should be sprayed with gasoline, acetone degreasing treatment, with a file, fine sandpaper, whetstone will remove the fatigue layer and the oxide layer, exposing the metal color. Then roughening treatment, roughening treatment can provide surface compressive stress, increase the bonding area and clean the surface of the coating and the substrate, reduce the stress when cooling the coating, ease the internal stress of the coating, it is conducive to the increase of adhesion . Sandblasting is the most commonly used roughening process, sand to sharp, hard as well, the choice of quartz sand, emery and so on. Rough fresh surface easily oxidized or polluted by the environment, it should be timely spraying, if placed more than 4h will be re-roughened. ⑵ surface preheat treatment The temperature difference between the coating and the substrate surface causes shrinkage stress on the coating, causing the coating to crack and peel off. Preheating of the substrate surface can reduce and prevent the above adverse effects. But the preheating temperature should not be too high, so as not to cause the substrate surface oxidation and affect the bonding strength of the coating and the substrate surface. Preheat temperature is generally 80-90 ℃, commonly used to complete the neutral flame. ⑶ spray bonding bottom Pre-spraying a thin layer of metal prior to applying the working coating provides a clean, rough surface for the subsequent coating to improve the bond strength and shear strength between the coating and the substrate. Bottom bonding materials generally use ferrochrome nickel alloy. The main principle of choosing the spraying process parameters is to increase the bonding strength between the coating and the substrate. Spray gun and the workpiece during the relative movement speed is greater than the flame moving speed, the speed of the size of the coating thickness, spray wire feeding speed, arc power and other parameters determined jointly. Spray gun and the surface of the workpiece is generally about 150mm. Other specifications for arc spraying are determined by the characteristics of the coating equipment and the coating material. ⑷ spraying working layer Wire brush should be used to remove the adhesion of the bottom surface of the sediment, and then immediately spray coating. Materials for the carbon steel and low alloy wire, the coating has a higher wear resistance, and lower prices. Spray coating thickness should be based on the amount of wear and tear of the workpiece, machining allowance and other relevant factors (diameter shrinkage, clamping deviation, spray coating diameter uneven amount, etc.) to determine. ⑸ cooling Spraying workpiece temperature rise is not high, usually directly air-cooled. ⑹ spray coating processing Mechanical processing to the required size of the drawing and the specified surface roughness. Gear pump sticky surface coating technology 1, the principle of surface coating and features In recent years, surface coating technology in China's equipment maintenance has been widely used for a variety of materials, parts and equipment repair. Its working principle is to add molybdenum disulfide, metal powder, ceramic powder and fiber and other special filler adhesive, directly applied to the surface of materials or parts, so that it has a wear-resistant, corrosion and other functions, mainly for surface strengthening and repair . Its process is simple, convenient and flexible, safe and reliable, does not require specialized equipment, just a good glue coated on the surface of the cleaned parts to be cured after curing can often operate at room temperature, will not make the parts Produce thermal equivalent effect and deformation. 2, sticky coating coating process Cylindrical sleeve, sleeve end face fit, gear end face or pump housing bore small area uniformity of wear between 0.15-0.50mm, scratch depth of 0.2mm or more, it is appropriate to use adhesive coating repair process. Adhesion coating coating process: initial cleaning → pre-processing → final cleaning and activation → preparation of repair agent → coating → curing → finishing, cleaning or post-processing. Although the sticky coating process is relatively simple, but the actual construction requirements are quite strict, just choose a good adhesive, not necessarily able to obtain high viscosity strength. It is necessary to choose the right adhesive, but also strictly in accordance with the correct process of adhesive coating the right adhesive, but also strictly in accordance with the correct process of law line viscosity coating in order to obtain a satisfactory effect. ⑴ initial cleaning Parts surface must not have grease, water, rust, dust and so on. Wash with gasoline, diesel or kerosene first, then acetone. ⑵ pre-processing Fine sand paper into a certain trench mesh, exposing the basic qualities of the substrate. ⑶ final cleaning and activation treatment With acetone or special cleaning agent. Then sandblasting, flame or chemical treatment to improve the surface activity. ⑷ preparation of repair agent Repair agent in use should be strictly in accordance with the provisions of the ratio of the agent (A) and curing agent (B) fully mixed to the same color as well, and run out within the prescribed time, with the accompanying. ⑸ coated Repair the surface with a thin coating on the stick repair surface, repeated scratching and parts fully infiltrated, and then evenly coated to the specified size, leaving a finishing allowance. As much as possible in the coating to move in one direction, the reciprocating coating will wrap the air in the gel to form bubbles or pores. ⑹ curing With coated release agent in the steel plate in the work, generally room temperature curing takes 24 hours, heating curing (about 80 ℃) takes 2-3 hours. ⑺ finishing, cleaning or post-processing To fine boring or with a file, fine sandpaper, stone to stick the surface finishing to the required size. Forged Grinding Mill Balls,Forged Mill Balls,Forging Balls For Sag Mill,Mill Balls For Abrasive SHANDONG SHENGYE GRINDING BALL CO., LTD , https://www.shengysteelball.com