When using spiral beneficiation equipment, the configuration must consider the size of the white to facilitate installation, maintenance, and proper use of the site. This configuration is reasonable if the distance between individual spiral beneficiation equipment can be replaced. When designing a concentrator, the slurry of the selected material should be considered for self-flow without the use of a centrifugal pump for feeding in and out. When installing equipment in an existing company, it is possible to use a pump to transport material. Spiral equipment is mostly installed in rows because it allows for reasonable use of the site area and allows the same product to be collected into the aggregates mounted below the equipment or combined under the lower elevation platform. This can shorten the length of the pipe selection. The three-head spiral beneficiation equipment with a 120 degree lower end of the spiral groove is required to operate from the side. This type of screw can also be installed in rows, but in order to facilitate the operation of the equipment, the rows must be kept at a certain distance. In this case, the product is discharged separately from the spiral groove, and the combination is only required to be below the elevation. The configuration of the spiral beneficiation equipment is mostly determined by the span of the production plant. The span of the production plant is mostly 6x6 or 6x9 meters. The span of the ore dressing section of the ore dressing plant is usually a multiple of 6 or 3. The equipment should be adapted to the arrangement of the columns, so that the front is not located on the main corridor, so that it will not hinder the operation. Several options for the configuration of spiral beneficiation equipment. When configuring the equipment, consider leaving a wide passage to ensure that the spiral beneficiation equipment can be transported on the aisle. At the same time easy to operate. The channel width is considered to be 750-1100 mm.
PC plastic,full name Polycarbonate.
PC plastic is a kind of excellent comprehensive performance engineering plastics.It has excellent physical, mechanical, electrical, and thermal properties,so it's known as the "king of the transparent plastic'
Classification:
Anti - static PC SHEET, conductive PC SHEET,fireproof PC SHEET,PC fiber - resistant, PC GF SHEET, PC+ABS SHEET,anti-ultraviolet ray resistance PC, food grade PC, anti - chemical PC.
Advantages:
1,Light weight
2,Impact resistance
3,Excellent physical, mechanical, electrical and thermal properties
4,Ultraviolet resistance
Disadvantages:
Polycarbonate is not resistant to ultraviolet light, no resistance to alkali, resistance to hydrolysis stability is not high, is the main performance defect is sensitive to the gap, resistance to organic chemistry, scratch resistance is poorer, long-term exposure to ultraviolet light yellow, are vulnerable to the erosion of some organic solvents.
Applications:
1. Dust-free room spacer
2. Equipment shield and test fixtures;
3. Commercial Building Lighting;
4. Soundproof walls;
5. Greenhouse;
6. Components for medical and pharmaceutical devices;
7. Face shields;
8. Skylights, etc
Modified use:
The purpose of the modified PC Plastic is to toughen, improve the processing performance, reduce the residual deformation, and increase the flame retardancy, etc.
PC/ABS can improve bending modulus, heat resistance and plating performance.
PC/PET and PBT can improve drug resistance and solvent resistance.
PC/PMMA added plexiglass to enhance the appearance of pearlescent color.
PC/PA and HIPS can improve impact toughness and surface finish.
PC/HDPE can improve water resistance, aging resistance, weather resistance and LDPE.
The PC Plastic USES fiberglass or carbon fiber to enhance modification and improve mechanical strength.
The flame retardant grade PC Plastic can be made with bromine flame retardant and antimony trioxide.
Other and polysulfone, aromatic polycarbonate, polyvinyl formaldehyde, polypropylene, polystyrene can be modified to achieve the balance between economy and performance.
Combustion characteristics:
Combustion condition: easy, softening foaming
Flame status: small amount of black smoke
After the fire: out of the fire
Bouquet: no special taste
Specification: the thickness of PC Plastic sheet material can be produced from 0.3mm to 1.9mm, the normal width is 600mm, the width cannot exceed 1200mm, the length is not limited.
Color: Black and clear, can also be made another color, and the color order is 500KG.
Modified varieties:PC Plastic can be added to the Glass Fiber, copper powder, and molybdenum disulfide enhancement plate according to customer's requirements.
Product certification: most environmental certification reports and safety reports for raw materials, such as SGS report, CTI report, UL report, MSDS safety information, etc.
PC Plastic Sheet,Esd PC Plastic Sheet,Fireproof PC Plastic Sheet,Abs Plastic Sheet Dongguan Noegem Plastic Products Co.,Ltd , https://www.noegempLastic.com
The thickness of plate can be produced from 2mm to 180mm, the usual specification of 2-10mm is 1000mm* 2000mm, and the commonly used specification of 10-180mm is 600*1200 mm. PC Plastic sheet can also be customized according to requirements, and the width cannot exceed 1200mm, and the length is not limited.and The diameter of the PC Plastic rod can be produced from 2mm to 250mm, the length is 1 meter, and it can be ordered to be more than 3 meters in length.
Add antistatic agent to the permanent plate, the volume resistance value of 10 to the 6 to 9 power.
Add flame retardant to the flame retardant board from UL 94v-0 to HB combustion grade, and other modification requirements are required to customize various additional properties according to the actual use of the customer.