First, the installation Assembly and disassembly 1. All parts to be installed scrub clean. 2. Install a mechanical seal on the motor shaft, add a small amount of clean turbine oil or 20 oil on the surface of the mechanical seal with static and dynamic fit. 3. Install impeller, fasten with impeller nut. 4. Install "0" ring, the pump body and the motor cover bolted words. Note that the gap between the impeller front cover and the pump body is 2 × 0.5 mm, and the impeller inlet outer ring and the pump body ensure a certain running clearance. 5. Disassembly order is the opposite. Installation and use 1. Use rubber gaskets and bolts to connect the flanges on both ends of the pump body to the flanges on the pipelines to complete the installation. In order to facilitate the use and maintenance, the pump inlet and outlet pipelines should be equipped with a control valve. 2. Open the inlet regulator , allowing water to enter the pump to keep the sealed chamber full of liquid (otherwise it will damage the seal) and close the outlet valve. 3. Turn on the power, jog to determine the correct steering. 4. Turn to determine, the pump starts, run. 5. Adjust the outlet valve opening so that the pump runs around the design point, depending on the pump's rated flow and near the head. For this purpose, it is best to install a pressure gauge near the outlet flange. Note: The pump is strictly prohibited running water, so as not to damage the seal. Second , SG-type pipe pump troubleshooting methods: malfunction the reason Method of exclusion No water pump Injected into the water pump is not enough, the rotation of the wrong direction, the impeller flow blockage. Fill the water pump again, the transmission impeller runner, adjust the rotation direction. 2. The pump flow is insufficient Partial pump blockage, the number of revolutions is too low, the total lift above the pump rating, impeller damage. Clean the pump and pipe, replace the impeller, increase the pump shaft rotation, adjust the outlet valve. 3. Outlet pressure is not enough Liquid in the air, the speed is too low, impeller damage, the outlet valve opening too large. Exclude the liquid air, increase pump speed, replace the impeller, adjust the small outlet valve. 4. pump power consumption is too large (motor fever) Mechanical defects such as running clearance is too small, the motor shaft bending, bolts and so on, the pump is working under too much flow that the pump is far below the rated head work. Check hiss? Block branded Barium Barium 调 ??? Adjust the outlet valve so that the pump at rated flow and lift near the work. Pump vibration Pipeline system support is not good, part of the impeller blockage caused by imbalance, resulting in cavitation, the liquid in the air. Check? Suck Mi С Norway? Tighten the nut, the impeller through the transmission to balance, remove the air. Pump leaks Damaged mechanical seal, 0-ring damage, pump body leakage. Replace the mechanical seal and 0 ring, welding pump body leakage. 7. Pump miso tone is too heavy Bearing overheating lack of oil, pump overload. Bearing Department refueling, according to 4 excluded. malfunction the reason Method of exclusion No water pump Injected into the water pump is not enough, the rotation direction is wrong, the impeller flow blockage. Fill the water pump again, the transmission impeller runner, adjust the rotation direction. 2. The pump flow is insufficient Partial pump blockage, the number of revolutions is too low, the total lift above the pump rating, impeller damage. Clean the pump and pipe, replace the impeller, increase the pump shaft rotation, adjust the outlet valve. 3. Outlet pressure is not enough Liquid in the air, the speed is too low, impeller damage, the outlet valve opening too large. Exclude the liquid air, increase pump speed, replace the impeller, adjust the small outlet valve. 4. pump power consumption is too large (motor fever) Mechanical defects such as running clearance is too small, the motor shaft bending, bolts and so on, the pump is working under too much flow that the pump is far below the rated head work. Check hiss? Block branded Barium Barium 调 ??? Adjust the outlet valve so that the pump at rated flow and lift near the work. Pump vibration Pipeline system support is not good, part of the impeller blockage caused by imbalance, resulting in cavitation, the liquid in the air. Check? Suck Mi С Norway? Tighten the nut, the impeller through the transmission to balance, remove the air. Pump leaks Damaged mechanical seal, 0-ring damage, pump body leakage. Replace the mechanical seal and 0 ring, welding pump body leakage. 7. Pump miso tone is too heavy Bearing overheating lack of oil, pump overload. Bearing Department refueling, according to 4 excluded. 2 Ton Electric Straddle Stacker
Zowell XEK20 2 ton electric straddle
stacker is standard with adjustable fork. It is a ideal forklift for both single
and double faced pallets. It is more easy to operate and
widely used in the food, medicine, tobacco, textile and car manufacturing
industry. It is the best choice for the customer who needs the short length and
high lift capacity. Combined with the powerful components and first class spare
parts make sure the electric reach stacker have best performance
Electric Stacker, or walkie stacker, is an
industrial device for loading and lifting pallets on a shelf at high level. As
an ideal choice to operate in narrow space of warehouse, it can be widely used
in petroleum, chemical, pharmaceutical, textile, pigment, coal and other industries,
as well as ports, railways, freight yards, warehouses.
Compared with the traditional manual stacking,
Zowell full electric stacker maintains great advantages in safety, efficiency
and cost. In addition to durability and accuracy both outside and inside,
Zowell XE electric stackers are also equipped with mast with clear view, double
speed and lateral vertical moving switch, which are valuable when working in
limited space.
The load capacity of XEK20 is 2 tons, it has two driving modes: walking and standing driving. If
you need bigger capacity or other customized options such as rod, low mast,
grabbling frame, please contact us so that we can provide you best solution
with professional knowledge.
walkie stacker with platform,semi electric straddle stacker,electric stacker port use,unicarriers pallet stacker
Suzhou Pioneer Material Handling Equipment & Technology Co., Ltd , https://www.xianfengforklift.com